Why do shower trays have Upstands?

As the name suggests, these shower trays have a 20mm high upstand around the perimeter on all 4 sides of the tray. The shower door and screens then sit inside these 'upstands' so that water cannot leak from any corner and is retained inside the shower box when in use.

.

Herein, what are Upstands on shower trays?

An upstand provides a small lip around the tray over which you can tile, or up to which you can place the frame of an enclosure.

are shower trays sloped? There are special waste traps made for shower trays which allow you to keep the tray as low to the floor as possible. The bottom of the tray is sloped to make sure the water runs out of the waste so you do not need to tilt it in any way.

Then, can all shower trays be raised?

Not all riser kits will fit all trays, so if you need to raise your shower tray, make sure the riser kit is compatible with it: some legs hammer into holes, some screw into female threads on the underside of the tray – it varies by manufacturer.

What is the best material for shower trays?

Acrylic Capped Stone Resin Increasingly the most popular material for modern shower trays, offering the best balance between weight and durability. Stone resin trays are made with shards of stone that are coated in a layer of molded resin, which is then polished into a smooth finish.

Related Question Answers

Do I need a riser kit for my shower tray?

Why would I need a riser kit for my shower tray? You may be able to place a shower tray directly on the floor. However, you must consider your waste water outlet. Trays should be fitted with a 'shower waste trap' which will protrude below the tray.

Are shower trays Non Slip?

Showering can be a slippery experience, especially when products are spilt, therefore we suggest that you purchase a Non-slip shower tray, these innovative trays are said to reduce the risk of slipping up to 5,000 times than if you were to install a standard shower tray!

How do you seal a shower tray?

Sealing a shower tray

1. Tools you'll need:
2. Ensure the area is dry.
3. Select the correct aperture size.
4. Cut the application nozzle.
5. Apply an even bead of silicone sealant.
6. Make sure there are no visible gaps.
7. Wipe the excess away.
8. Smooth out the sealant.

What is a riser kit?

A shower riser kit is a rigid option for your shower which is generally fixed in position and set to a preferred height. A full kit includes the rigid riser (rail) and shower head; and with some shower riser kits there is an additional handset connected via a flexible hose and switched between using a diverter.

What is a tile upstand?

A tiling upstand is typically a 22mm integral vertical extension that is applied to two or three siles of a shower tray. During installation, this provides a watertight finish between the tray and the finished wall surface.

What is an upstand?

In kitchen terms, an upstand is a small strip of kitchen worktop, glass or acrylic usually 100-150mm in height that fits in the rear wall edge of your kitchen worktop.

How do you fit a shower tray to a solid floor?

Apply a thin bed of flexible adhesive to the area where the tray is to be secured using a notched trowel. Fit the shower tray over the bed of adhesive and firm down ensuring the tray is level in all planes Identify the position of the drain and trap and remove any existing concrete to a depth of approx.

How do I raise my shower base?

It is not hard to raise the level of the shower base, but remember not to block the drain weep holes.

1. Step 1 - Mark Out the Shower Tray.
2. Step 2 - Place a PVC Pipe Over the Waste.
3. Step 3 - Make Sure There Is Fall.
4. Step 4 - Check the Pipe.
5. Step 5 - Fill the Dam.
6. Step 6 - Tile the Bricks.
7. Step 7: Apply Sealant.

How do I stop my shower tray from moving?

Spray foam filler into the gap around the shower tray ensuring it goes under the tray, you will need to mask the shower tray and walls. Once you have done that then place a bag of sand in the shower tray to weigh it down, leave for 48 hrs. Then remove the sand and cut off any excess foam and re-silicone.

How do you level a wood floor for a shower base?

How to Level a Floor for a Shower Base

1. Vacuum and clean the floor thoroughly.
2. Go to the marked areas one at a time and lay down shims.
3. Screw down the shims with your galvanized flat-head screws and screw gun.
4. Sweep and damp-mop the floor to remove dirt and dust.
5. Apply leveling compound to the shimmed floor.
6. Spread the leveling compound flush with the shims.

Should I drill a stone resin shower tray?

Some manufacturers shower doors. Especially, the frameless ones, need a positive fixing into the tray. On a stone resin tray a normal masonry bit will be fine. Put a spot of silicone over the wall plug before screwing down.

What do I need for a walk in shower?

Consider construction costs. Generally, building a walk-in shower requires gutting walls to access plumbing pipes, applying waterproof poly sheeting to the walls and floor, rebuilding walls using moisture-resistant drywall or backer board, installing drains, and pouring mortar to create shower pans.

What is the minimum fall for shower waste?

Waste pipes need to be installed sloping down to ensure the water runs the right way. This needs to be a minimum of 10mm fall for every 4m of pipe which can lead to insufficient fall within the floor void under baths or showers (especially under low-level or flush shower trays).

Can you have a walk in shower upstairs?

Yes, it can be done, no it's not difficult and no you won't get leaks (providing the work is carried out correctly). In looking at the pros and cons of this issue, it is interesting to consider the main differences between a conventional shower area and a wetroom.

Can you cut shower trays?

Yes, it is very simple; all you need is a sharp blade. The trays are supplied in standard sizes and can be easily cut to the exact measurements required before installation.

How do you plumb a low profile shower tray?

1. Mark Out The Tray Position. Place your new shower tray in the general position you intend to fit it.
2. Choose The Waste Position.
3. Line Up Side Panels.
4. Check The Tray Is Level.
5. Attach The Waste.
6. Apply Sealant.
7. Complete The Surrounding Walls.
8. Install Side Panels.

How high can you raise a shower tray?

Raised shower trays To do this, you need to get a shower tray riser kit. Visually, a raised shower tray is less appealing, so it's best avoided unless it's necessary for installation. It will usually bring the height of your tray up to around 140mm.

How deep should a shower tray be?

The average width and depth of a shower tray is typically between 700mm and 1700mm.

How do you fit a resin shower tray?

Put the plywood in position, ensuring the area is flat and level. Place the shower tray A on the plywood and mark the waste hole location. Remove the shower tray then use the hole cutter to drill a hole in the plywood large enough to pass through the entire waste unit. Keep all holes to the minimum.